:: www.honda-club.cz ::

Re: B18c Spec R

SpaceMan — 18.2.2015 , 20:40

Autor: SpaceMan

Zaslal: 18.2.2015 , 20:40

What about CR-X del Sol (EH6/EG2)? It will be awsome... One of the fastest del Sol in Czech Rep.

Re: B18c Spec R

ge.nnc — 18.2.2015 , 20:03

Autor: ge.nnc

Zaslal: 18.2.2015 , 20:03

@Space Man :im between crx and civic ej9
@Street Kid : Its going to be semi build all motor with skunk2 head package and hi comp pistons

Re: B18c Spec R

Streetkid — 18.2.2015 , 19:58

Autor: Streetkid

Zaslal: 18.2.2015 , 19:58

Nice ITB, but are you sure that 52 mm is good diameter for fine tuning on your 1.8 engine? 52 mm is maybe acceptable for hardcore high HP projects I think and some guys had issues with this kind of big diameter - it makes low velocity speed in plenum and kill advantages of ITB's - good midrange and fast response

Re: B18c Spec R

SpaceMan — 18.2.2015 , 13:02

Autor: SpaceMan

Zaslal: 18.2.2015 , 13:02

Hi Genc,
good job on engine. Did you find a car for your project?

Good luck!

Re: B18c Spec R

ge.nnc — 18.2.2015 , 7:59

Autor: ge.nnc

Zaslal: 18.2.2015 , 7:59

New Valve seals

and TWM ITB 52mm Air Horn Carbon complete with fuel rail ,fuel regulator ,fuel pressure regulator,vacuu lines, map sensor ,tps sensor ,air sensor

some polishing job

[img][/img]
[img][/img]
[img][/img]
[img][/img]

Re: B18c Spec R

ge.nnc — 5.9.2014 , 19:30

Autor: ge.nnc

Zaslal: 5.9.2014 , 19:30

Here are some photos during the work

Dual Valve Springs

Look what i found inside valve springs

Working into head with dremel

B18c block with arp head studs

P73 00 ITR SPEC R pistons 11.1 compresion ratio

Opel haters

Fel Pro Gasket and Moroso Racing Oil Pan

JDM R Crankcase sign

DC 4-2-1 Ceramic Coated Header
Innovative Engine Mounts
Msd Igniton + 10 mm Cables
Gearbox intermediate shaft
New Timing Belt with tensioner
etc

Throttle Body Port-Matching 2mm in each side
Skunk2 Pro Intake manifold 64mm port maching with 70MM Skunk2 Throttle body

Cleaning Valves

Thanks For Watching

Re: B18c Spec R

ge.nnc — 5.9.2014 , 18:47

Autor: ge.nnc

Zaslal: 5.9.2014 , 18:47

83427 napsal:

good job on the head. polished ports looks very clean. how you did it? with dremel?

anyway interesting project. iam will keep an eye on it

yes i use dremel and sandpaper from 240-2000 water sandpaper
i worked for 2 weeks day by day 1-2 hour in day
I not supposed to finish work quickly, because if you work more than 1-2 hours a day,
will get tired from sanding and nerves will begin
and you will start to finish job as soon as possible

Re: B18c Spec R

83427 — 5.9.2014 , 7:48

Autor: 83427

Zaslal: 5.9.2014 , 7:48

good job on the head. polished ports looks very clean. how you did it? with dremel?

anyway interesting project. iam will keep an eye on it

Re: B18c Spec R

Koubelec — 4.9.2014 , 0:12

Autor: Koubelec

Zaslal: 4.9.2014 , 0:12

I think he uses google translater and that's not so good in this case.. Impressive project, i wish you good luck in next steps RESPECT

Re: B18c Spec R

Blackburn — 3.9.2014 , 19:53

Autor: Blackburn

Zaslal: 3.9.2014 , 19:53

USA...country without borders

Re: B18c Spec R

ge.nnc — 3.9.2014 , 19:46

Autor: ge.nnc

Zaslal: 3.9.2014 , 19:46

hahaha Mnoho přítele spolu se mnou na můj projekt, protože každý Koupě prvního projektu Startovací vysušuje motor, ale motor si koupili, protože jsem byl v USA a já jsem šel koupit přímo od JDM motoru IMPORT, ne mám nechat výběr případ v USA a Vzhledem k tomu, vrací bez zakoupení motorového tento motor v Evropě bude příliš expensiv
Omlouvám se za moje špatná čeština

Re: B18c Spec R

Blackburn — 3.9.2014 , 19:36

Autor: Blackburn

Zaslal: 3.9.2014 , 19:36

Welcome
Nice job (my english is not ok )
You have started with engine and next step will be car It's impressive process.

I have CRX 2G. It's cult car for every swap.
Next favorit for me is civic 6G-EK

I'm watching your page

English vs. Czech

Kleeman — 3.9.2014 , 14:36

Autor: Kleeman

Zaslal: 3.9.2014 , 14:36

You said your Czech is not very good, but I don´t think so... Translation : Nech být angličtiny a piš česky. Píšeš líp česky, jak jedna třetina uživatelů tady na fóru

Re: B18c Spec R

ge.nnc — 3.9.2014 , 12:51

Autor: ge.nnc

Zaslal: 3.9.2014 , 12:51

I still dont have a car ,i am a honda civic EJ-EK fan but maybe i will buy a civic EF or Crx ED-EE8

Pořád nemám auto, jsem fanoušek Honda Civic EJ-EK, ale možná budu kupovat civic EF nebo CRX ED-EE8

Re: B18c Spec R

ge.nnc — 3.9.2014 , 12:47

Autor: ge.nnc

Zaslal: 3.9.2014 , 12:47

This are photo when i made a box for shipping

Toto jsou fotografie, kdy jsem udělal pole k odeslání

Here is the head job done by me
When i open the head it was in this condition
Also i bought ARP head Studs

Zde je úkol mě hlava
Když otevřu hlavu to bylo v tomto stavu
Také jsem si koupil ARP hlavy Studs Doprava